Temperature management
-
Zennio MAXinBOX FC 0-10V fan-coil and/or valves - ZCLFC010
Zennio MAXinBOX FC 0-10V fan-coil and/or valves - ZCLFC010
Controller for 2-pipe or 4-pipe fan-coil units with 2 x 0–10 V outputs for control of fan and/or valves and 4 relay outputs (16 A C-Load) for fan speed or on/off valve control. The outputs not used can be used for other control purposes. It has 4 analog-digital multifunction inputs that can be configured as binary inputs for sensors and potential-free push buttons, as temperature probe inputs or as motion sensor inputs. It also includes 2 thermostats, 10 logical functions and allows manual control of the outputs with status indication through LEDs. DIN rail mounting (4 modules). It is compatible with KNX Secure. Accessories: temperature probe and motion sensor
204.30 € -
Zennio MAXinBOX FC 0-10V FAN-ZCL-FC010F
Zennio MAXinBOX FC 0-10V FAN-COIL Controller ZCL-FC010F
MAXinBOX FC 0-10V FAN :
Controller for up to two 2-pipes or 4-pipes fan coil units with on/off valves and 0-10 V fan speed control signal. Mounted on DIN-rails (4.5 units). 4 multifunction outputs (16 A C-Load) that can be used for the control of the fan coil on/off valves or any other purpose. 4 analog-digital multifunction inputs that can be configured as binary inputs for sensors and potential-free push buttons, as temperature probe inputs or as motion sensor inputs. It also includes 2 thermostats and 10 logical functions. Manual control of outputs and status indication through LEDs. Accessories: temperature probe and motion sensor.
168.00 € -
Zennio Fan-coil controller for a 2-Pipe or 4-Pipe fan coil with 0-10 DC valves-ZCL-FC010V
Zennio Fan-coil controller for a 2-Pipe or 4-Pipe fan coil with 0-10 DC valves-and up to 4 fan speeds-ZCL-FC010V
MAXinBOX FC 0-10V VALVE :
Controller for one 2-pipes or 4-pipes fan coil unit with 0-10 V valves. Its 4 outputs (16 A C-load) can be used to control the fan speed or as individual outputs. it has 4 analog-digital multifunction inputs that can be configured as binary inputs for sensors and potential-free push buttons, as temperature probe inputs or as motion sensor inputs. It also includes 2 thermostats, 10 logical functions and allows manual control of the outputs with status indication through LEDs. DIN-rail mounting (4.5 units). Accessories: temperature probe and motion sensor.
168.00 € -
Zennio MINiBOX 0-10V X1 Multifunction actuator with 1 0-10 V input/output analog channel ZIO1X010
Zennio MINiBOX 0-10V X1 Multifunction actuator with 1 0-10 V input/output analog channel ZIO1X010
DIN rail mounting actuator (2 DIN wide) with 1 channel configurable as 0-10 V output, 0-10 V input or 4-20 mA input. It includes fan coil module for installations where either the valve or the fan are 0-10 V signal controlled and the remaining are controlled by an external device.
Manual control is available using the push button and the channel’s status is shown via the LED indicator.
It includes 10 logic functions and 1 thermostat.
108.00 € -
Zennio MINiBOX 0-10V X2 Multifunction actuator with 2 0-10 V input/output analog channels ZIO2X010
Zennio MINiBOX 0-10V X2 Multifunction actuator with 2 0-10 V input/output analog channels ZIO2X010
DIN rail mounting actuator (2 DIN wide) with 2 channels configurable as 0-10 V outputs, 0-10 V inputs or 4-20 mA inputs. Each channel can be configured individually or jointly to control a 2-pipe fan coil where both fan and valve are controlled with 0-10 V signals.
Manual control is available using the push buttons and each channel’s status is shown via the LED indicator
It includes 10 logic functions and 2 thermostats
119.40 € -
Zennio MINiBOX 0-10V X3 Multifunction actuator with 2 0-10 V input/output analog channels ZIO3X010
Zennio MINiBOX 0-10V X3 Multifunction actuator with 3 0-10 V input/output analog channels ZIO3X010
DIN rail mounting actuator (2 DIN wide) with 3 channels configurable as 0-10 V outputs, 0-10 V input or 4-20 mA input. Each channel can be configured individually or jointly to control 2-pipe or 4-pipe fan coils where fan and valves are controlled with 0-10 V signals.
Manual control is available using the push buttons and each channel’s status is shown via the LED indicator.
It includes 10 logic functions and 3 thermostats.139.80 € -
Schneider-KNX-Valve Drive Controller-MTN6730-0002
Schneider-KNX-Valve Drive Controller-MTN6730-0002
It is used to operate thermal servo-motors designed to control
control of hydraulic floor heating or cooling ceilings.
The actuator has 6 electronic outputs. Up to
connect up to 4 230 Vac thermal actuators or 2 24 Vac thermal
24 Vac thermal actuators to each output. Actuators
normally closed or normally open actuators can be
connected.
In addition, the actuator has 6 integrated temperature regulators
which operate independently of each other.
The correction variables of the controller outputs can be
connected internally to the actuator outputs, so that temperature
so that temperature control and servomotor actuation can be performed
can be carried out by a single device on the bus.
The integrated temperature controllers can send the
correction variable telegram on the bus and thus control other
control other heating or fan coil actuators.
The outputs are either switched (1 bit) or PWM (1
byte).
Each output is protected against overload and short-circuit.
All outputs can be controlled manually using
front panel pushbutton.
Panel mounting on rails.
The bus is connected via a bus terminal.352.80 € -
Siemens KNX Thermal drive actuator-6 x AC 24/230 V - 5WG1605-1DB41
Siemens KNX Thermal drive actuator-6 x AC 24/230 V - 5WG1605-1DB41
Additional functionalities GAMMA- For control of electrothermal valve drives for AC 24...230 V in heating/cooling systems via 6 noiseless semiconductor outputs
- Electronic protection of the outputs against short circuit and overload
- Rated current: 0.5 A per channel and group of 3 outputs
- Max. inrush current (2 sec.): 3.5 A per channel and group of 3 outputs
- Max. inrush current (2 min.): 0.9 A per channel and group of 3 outputs
- Direct operation per channel for opening and closing the valve and activating direct operation
- Red LED per channel to indicate valve open or closed and status of the control value
- Red error LED per channel to indicate overload/short circuit and pover voltage failure
- Maintenance-free terminals for connection and through-wiring of untreated single-core, stranded or multi-core conductors, 0.5 ... 2.5 mm²
- 2 terminals per channel for connecting the electrothermal valve drives
- 2 terminals on the unit for supply of the valve voltage AC 24...230 V
- Bus-powered electronics
- Housing: plastic, color RAL 7035, N-system
- DIN rail mounted device for mounting on rail TH35 according to DIN EN 60715
- Type of protection: IP 20
- Per channel setting of the valve operation direction de-energised open or closed
- Per channel optional control via switching commands or continuous positioning commands
- Per channel control value limitation and adjustment of the valve characteristic for continuous control values
- Per channel control value monitoring
- Adjustable behaviour in case of override (lock, service mode, forced position, forced control)
- Per output automatic, demand-oriented or manual valve rinsing
- Per output operating hours counting and switching cycle counting with limit value monitoring
- Evaluation of control values for heating or cooling demand requirements on a primary system and for controlling heating or cooling circuit pumps
- 6 room temperature controllers for 2-pipe or 4-pipe systems, adjustable as 2-position control or continuous control, for heating-only mode, cooling-only mode, heating and cooling mode, with two-stage heating or cooling
- Output of the control values optionally as switching command On/Off or as continuous control command
- 13 min., max. and weighted value calculators
- 6 logical operations (AND/OR/XOR/TRIGGER/LOCK)
- Surveillance of device function
198.00 €
