Zennio EyeZen TP KNX motion detector with light sensor ZPDEZTPA-ZDPEZTPVTA

ZPDEZTPA replaced by Temporary Version ZDPEZTPVTA

Check in the PDF Retrieved references & Temporary references in Documents

The replacement of the product is due to the worldwide situation of shortage of components that we are experiencing and that has forced us to change the microcontroller with another of the same model but different capacity to ensure continuity of deliveries.

This change obliges us to compile the application program again for this microcontroller and it implies a new software register at KNX for each new reference.

The ETS application programs for these products are different, but the functionality is maintained.

(EyeZen_TP_vT_1.4_EIFAItR_ETS5_Cert.knxprod)

KNX motion detector with brightness sensor for ceiling installation, with a 360º detection area and up to 6 metres in diameter. It includes several configurable channels for constant lighting variation, switched control of the lighting according to a brightness threshold or according to motion detection only. It is possible to adjust the sensitivity of each sensor independently and to calibrate the lighting of the work surface. Master/slave configuration allows multiple sensors to be used for large areas. Recessed installation.

Zennio EyeZen TP KNX motion detector with light sensor ZDPEZTPW-ZDPEZTPVTW

ZPDEZTPW replaced by Temporary Version ZDPEZTPVTW 

Check in the PDF Retrieved references & Temporary references in Documents

The replacement of the product is due to the worldwide situation of shortage of components that we are experiencing and that has forced us to change the microcontroller with another of the same model but different capacity to ensure continuity of deliveries.

Replacement of references in your order with devices (vT) Temporary version

This change obliges us to compile the application program again for this microcontroller and it implies a new software register at KNX for each new reference.

The ETS application programs for these products are different, but the functionality is maintained.

(EyeZen_TP_vT_1.4_EIFAItR_ETS5_Cert.knxprod)

KNX motion detector with brightness sensor for ceiling installation, with a 360º detection area and up to 6 metres in diameter. It includes several configurable channels for constant lighting variation, switched control of the lighting according to a brightness threshold or according to motion detection only. It is possible to adjust the sensitivity of each sensor independently and to calibrate the lighting of the work surface. Master/slave configuration allows multiple sensors to be used for large areas. Recessed installation.

Zennio EyeZen IN Motion detector with luminosity sensor ZPDEZINA

This accessory must be connected to an input of a Zennio device. To find out if a device is compatible with this accessory, consult the data sheet of the device in question.

The motion sensor with infrared detection technology is complemented by an integrated luminosity sensor, which makes the device even more useful. Directly connected to input of a Zennio device. Motion detection area can be increased by installing two sensors in parallel, to the same input. Easy installation and small size. It does not require any other type of connection or power supply.

Zennio EyeZen IN Motion detector with luminosity sensor ZPDEZINW

This accessory must be connected to an input of a Zennio device. To find out if a device is compatible with this accessory, consult the data sheet of the device in question.

The motion sensor with infrared detection technology is complemented by an integrated luminosity sensor, which makes the device even more useful. Directly connected to input of a Zennio device. Motion detection area can be increased by installing two sensors in parallel, to the same input. Easy installation and small size. It does not require any other type of connection or power supply.

Theben theRonda S360 KNX FLAT DE WH 2089560

• Passive infra-red presence detector KNX for ceiling installation
• Circular detection area 360°,Ø 8 m, (50 m2 ) at mounting height 3 m
• 2 channels light and 2 channels presence
• Mixed light measurement
• 2 light channels C1, C2
• Switching operation or constant light control with standby function (orientation light)
• Switching mode with dimmable lighting
• Choice of fully or semi-automatic
• Brightness switching value or set point value can be set in lux by using parameters or via the object
• Teach-in of the brightness switching value or the set point value
• Reduction of time delay when present briefly (short-term presence)
• Manual override by telegram or remote control
• 2 presence channels C4, C5, individually configurable
• Switch-on delay and time delay configurable
• Setting the room correction factor for brightness measurement comparison
• Adjustable sensitivity
• Test mode for checking function and detection area
• Scenes
• Parallel switching of multiple presence detectors (Master/Slave or Master/Master)

Theben thePixa P360 KNX UP WH : 

• Optical presence detector for ceiling installation
• KNX Data Secure
• Rectangular detection area with up to 6 flexible detection zones (Total area 11.0 x 15.5 m │171 m²; at 4.5 m installation height)
• Restriction of the detection area via app (thePixa Plug)
• Automatic presence and brightness-dependent control for lighting and HVAC
• Each detection zone has its own light measurement
• Adjustment of brightness measurements via thePixa Plug app
• Configurable sensitivity of sensor
• Distinction between motion and presence
• Parallel switching of multiple presence detectors (Master/Slave or Master/Master)

Zennio Presentia C v2-vT KNX ceiling presence detector with light sensor ZPDC30LV2-ZPDC30LVT

ZPDC30LV2  replaced by Temporary Version ZPDC30LVT

Check in the PDF Retrieved references & Temporary references in Documents

Presence detector with luminosity sensor for ceiling mounting, with a detection area of 360º and up to 30 meters diameter. It includes several channels to be configured for constant luminosity regulation, lighting switching control according to luminosity threshold or according to presence detection only. Sensitivity settings can be adjusted for each sensor individually and luminosity can be calibrated to the working environment values. Master/slave configuration allows using several detectors for larger areas. Flush mounted or surface mounted (accessory included).

Zennio motion detector ZN1IO-DETEC-X

Motion sensor with infrared detection technology. Directly connected to input of a Zennio device. Motion detection area can be increased by installing two sensors in parallel, to the same input. Easy installation and small size. It does not require any other type of connection or power supply.

* This accessory must be connected to an input of a Zennio device:

To which Zennio devices can I connect a motion detector?

Motion detectors can be connected to Zennio devices with analog-digital inputs.

Zennio devices have two input types :

-       Binary inputs: to connect push buttons/switches.

-       Analog-digital inputs: to connect motion sensors or temperature probes. Also configurable as binary inputs.

*Inputs not available for luminosity sensor functionality.

If the device allows the connection of a motion sensor,  at its website tools section you will find the motion sensor manual.

How can I know the position where the micro switch must be placed (Type A/B)?

Depending on the device where the motion sensor is connected, the micro switch must be placed at the position A or B. To know which position corresponds to your device, it is necessary to check the device datasheet to which the motion sensor will be connected.

 Do I need an external power supply for the sensor?

No, you just need to connect it to the inputs of the devices allowing its control

 What is the detection area covered by a Zennio motion sensor?

This feature depends critically on the location of the device. In particular, for a detector located in the ceiling of a room, the detection area can be doubled if you double the height at which it is placed. For further information, consult the documents.

 How should I install the motion sensor to get the most of its functionality?

In the Motion Sensor area, you can download the installation note in documents that includes installation tips to find the most suitable place to be placed.

 How is the luminosity level measured by the sensor sent to the bus? (Only ZN1IO-DETEC-P)

The sensor sends a luminosity level in the range [1.....100] through a 1 byte Communication Objet. In any case this is a a 2 bytes object with the value measured in LUXES.

 Can we cancel the LED blinking everytime there is a detection?

Yes, using the micro switch at the rear of the device.

What is the maximum length allowed for the wiring of the analogue inputs?

The wiring of the analogue inputs can be extended up to 30 meters using a cable with a section between 0.15 mm2 and 1 mm2.

The luminosity sensor does not measure correctly. (Only ZN1IO-DETEC-P)

Check if the microswitch number 2 is placed in the correct position. You can find this information in the data sheet of the device to which it is connected.