Skip to content

Input module


  • Interra 2 channels Universal interface ITR102

    Interra ITR102 :

    Description : 

    ITR102 device is used to interface the contacts to KNX bus substructure such as push buttons, switches etc. to make them communicating devices.

    Configuration and features : 

    • The complete configuration of the device is performed via ETS3 or higher.
    • Depending on ETS configuration and settings the product feature will be different.
    • Avaialble functions are:
      • Switching
      • Dimming
      • Toggle
      • Blind Control
      • 2 Channel
      • Value Selected
    • Most of functions only need one input and therefore each input might be assigned a different function. However there are also some functions which use two inputs such as “Dimming with 2 buttons” and “Shutter/Blinds with 2 buttons”.

    Mounting, commissionning and safety notes : 

    • The device may only be installed and put into operation by a qualified electrician or authorized personnel.
    • The device is inserted in a flush-mounted combined joint box.
    • The installation location should not be in the outdoor area.
    • The voltage potentials on the lines connecting the contacts are not electrically isolated from the bus voltage.
    • Permitted cable length can be up to 5 meters and unused wires should be insulated.
    • Avoid contact with liquids and corrosive gases.
    • Do not get wrong connection for KNX Black and Red wires.
    • Please do not forget to recheck all connections after installation

    44.50 €
  • Schneider-Push-button interface, 2-gang plus -MTN670802

    Schneider-Push-button interface, 2-gang plus -MTN670802

    Push-button interface, 2-gang plus. Generates an internal signal voltage for connecting 2 conventional push-buttons or floating contacts, and for connecting 2 low-current LEDs. The cores are 30 cm long and can be extended to max. 7.5 m. For installation in a conventional 60 mm switch box. KNX software functions: Switching, dimming or controlling blinds via 1 or 2 inputs, position values for blind control (8-bit), pulse edges with 1-, 2-, 4-, or 8-bit telegrams. Differentiation between short and long activation, initialisation telegram, cyclical transmission, pulse edges with 2-byte telegrams, 8-bit linear regulator, scenes. Counter, disable function, break contact/make contact, debounce time. Outputs for connecting control lamps (low-current LEDs) for the status display. For each input/output object type: Contact voltage: < 3 V (SELV). Contact current: < 0.5 mA. Output current: max. 2 mA. Max. cable length: 30 cm unshielded, can be extended up to max. 7.5 m with twisted unshielded cable. Dimensions: approx. 40x30.5x12.5 mm (LxWxH). Colour: polar white.

    44.40 €
  • Interra 4 channels Universal interface ITR104

    Interra ITR104 :

    Description : 

    ITR104 device is used to interface the contacts to KNX bus substructure such as push buttons, switches etc. to make them communicating devices.

    Configuration and features : 

    • The complete configuration of the device is performed via ETS3 or higher.
    • Depending on ETS configuration and settings the product feature will be different.
    • Avaialble functions are:
      • Switching
      • Dimming
      • Toggle
      • Blind Control
      • 2 Channel
      • Value Selected
    • Most of functions only need one input and therefore each input might be assigned a different function. However there are also some functions which use two inputs such as “Dimming with 2 buttons” and “Shutter/Blinds with 2 buttons”.

    Mounting, commissionning and safety notes : 

    • The device may only be installed and put into operation by a qualified electrician or authorized personnel.
    • The device is inserted in a flush-mounted combined joint box.
    • The installation location should not be in the outdoor area.
    • The voltage potentials on the lines connecting the contacts are not electrically isolated from the bus voltage.
    • Permitted cable length can be up to 5 meters and unused wires should be insulated.
    • Avoid contact with liquids and corrosive gases.
    • Do not get wrong connection for KNX Black and Red wires.
    • Please do not forget to recheck all connections after installation

    53.50 €
  • Schneider-Push-button interface, 4-gang plus -MTN670804

    Schneider-Push-button interface, 4-gang plus -MTN670804

     

    Push-button interface, 4-gang plus. Generates an internal signal voltage for connecting 4 conventional push-buttons or floating contacts, and for connecting 4 low-current LEDs. The cores are 30 cm long and can be extended to max. 7.5 m. For installation in a conventional 60 mm switch box. KNX software functions: Switching, dimming or controlling blinds via 1 or 2 inputs, position values for blind control (8-bit), pulse edges with 1-, 2-, 4-, or 8-bit telegrams. Differentiation between short and long activation, initialisation telegram, cyclical transmission, pulse edges with 2-byte telegrams, 8-bit linear regulator, scenes. Counter, disable function, break contact/make contact, debounce time. Outputs for connecting control lamps (low-current LEDs) for the status display. For each input/output object type: Contact voltage: < 3 V (SELV). Contact current: < 0.5 mA. Output current: max. 2 mA. Max. cable length: 30 cm unshielded, can be extended up to max. 7.5 m with twisted unshielded cable. Dimensions: approx. 40x30.5x12.5 mm (LxWxH). Colour: polar white.

    64.50 €
  • Interra 6 channels Universal interface ITR106

    Interra ITR106 :

    Description : 

    ITR106 device is used to interface the contacts to KNX bus substructure such as push buttons, switches etc. to make them communicating devices.

    Configuration and features : 

    • The complete configuration of the device is performed via ETS3 or higher.
    • Depending on ETS configuration and settings the product feature will be different.
    • Avaialble functions are:
      • Switching
      • Dimming
      • Toggle
      • Blind Control
      • 2 Channel
      • Value Selected
    • Most of functions only need one input and therefore each input might be assigned a different function. However there are also some functions which use two inputs such as “Dimming with 2 buttons” and “Shutter/Blinds with 2 buttons”.

    Mounting, commissionning and safety notes : 

    • The device may only be installed and put into operation by a qualified electrician or authorized personnel.
    • The device is inserted in a flush-mounted combined joint box.
    • The installation location should not be in the outdoor area.
    • The voltage potentials on the lines connecting the contacts are not electrically isolated from the bus voltage.
    • Permitted cable length can be up to 5 meters and unused wires should be insulated.
    • Avoid contact with liquids and corrosive gases.
    • Do not get wrong connection for KNX Black and Red wires.
    • Please do not forget to recheck all connections after installation

    64.00 €