Interra 640mA KNX power supply ITR900-0164

Interra 640 mA KNX Power Supplies generate and monitor bus voltage (SELV) for the KNX devices connected to the bus. They have 640 mA busloads with an integrated choke and wide-range mains input for worldwide usage. The bus line is decoupled from the power supply by an integrated choke. The voltage output is short-circuited and overload protected. The two-color LED indicates (Green and Red) device output status. It has a wide range of input from 85…265 V AC, to 50/60 Hz.

Interra Just Touch ITR328-1001 : 

• Pushbutton has Switching, toggle, dimming, shutter/blinds, thermostat controls, scenes, value, 2 channels, step switching mode features.
• Locking feature available for each button and complete device
• On/Off (2-points) and Proportional (Continuous or PWM) thermostat functions.
• Comfort, standby, economy and building protection operating modes.
• Manual or Automatic switching between Heating and Cooling modes.
• Temperature measuring through integrated sensor with possibility of sending the value on change and periodically to the bus.
• Temperature (measured, external, setpoint, outdoor values as ºC), CO2 concentration (from bus), humidity percentage, operating modes, fan levels, on/off indicators, warnings and locking status are displayed on screen.
• Fan controller available with different speed indicators.
• Relative humidity measuring through the integrated sensor with possibility of sending the value on the bus.
• Threshold alarm define for temperature, humidity and air quality levels.
• RGB LED control.

Interra Combo ITR508-16A

• Lighting control can be made with every output of the combo switch actuator.
• Heating control can be made with every output of the combo switch actuator.
• Every output of the combo module can be configured as shutter/blind provided that 2 consecutive outputs are available.
• Shutter/blind 24V configuration can be with 4 outputs of the combo module. However, it is only available in the first four outputs of the (*) blocks.
• Fan Coil 2 pipes configuration can be with 4 outputs of the combo module. However, it is only available in the first four outputs of the (*) blocks.
• Fan Coil 4 pipes configuration can be with 5 outputs of the combo module. However, it is only available in the first five outputs of the (*) blocks.
• The functionalities for each output include among other things timing functions, logic gates, scenes, disabling function, forced, working hours counter, periodical monitoring and different configurations for feedback telegrams.
• Last situation memory against power failure.
(*): Each block consists of every 6 outputs of the combo module that is starts from C1 output.

Interra Daikin Sky AC - KNX Gateway ITR830-0003

ITR830-0003 is an air conditioner gateway used for monitoring and controlling all the functioning parameters of Daikin Industries air conditioners via the KNX bus line. Daikin Sky & VRV AC - KNX Gateway is compatible with models in Sky & VRV types categorized in the compatibility list sold by Daikin Industries. Daikin Sky & VRV AC - KNX Gateway has an easy installation feature and can be installed inside the own AC indoor unit or a proper location away from the air conditioner, it connects one side directly to the electronic circuit of the AC indoor unit and in the other side directly to the KNX bus.

Main Functions:

•  ITR830-0003 device provides complete bidirectional integration of Daikin Sky & VRV air conditioners with KNX bus. 

• Includes 4 logical advanced parameters, each logical parameter has up to 4 inputs and can be configured as AND, OR & XOR. 

• Includes 8 advanced converter parameters, each converter has four operations math calculations according to the input type. 

• Logic and converter parameters can be used for energy savings, configurable scenes, temperature limits etc. 

• The Daikin air conditioner unit provides error notifications for errors that may occur in exceptional cases.

Interra Daikin Split AC - KNX Gateway ITR830-0002

ITR830-0002 is an air conditioning interface for monitoring and controlling all functional parameters of Daikin Split air conditioners via KNX line. The Daikin Split AC - KNX interface works compatible with models sold by Daikin and classified as Split in the compatibility list. Thanks to its easy installation feature, Daikin Split AC - KNX interface can be installed on the indoor unit of the air conditioner to be installed or in a suitable location away from the air conditioner. Daikin Split AC - KNX interface is installed by connecting one side directly to the electronic circuit of the AC indoor unit and the other side directly to the KNX bus.

Main Functions:

•  The ITR830-0002 interface allows bidirectional integration of Daikin Split air conditioners with the KNX bus.

 •   ITR830-0002 includes 4 logical advanced parameters, each logical parameter can contain up to 4 inputs with logic conditions and can be configured as OR, AND & SPECIAL OR logical operator.

 •  The ITR830-0002 includes 8 advanced transducer parameters and each transducer can perform four operation calculations depending on the input type.

 •  Logical and transducer parameters can be used for energy saving, configurable scenarios, temperature limits, etc.

 •   The Daikin AC unit has error notifications for errors that may occur in exceptional cases.

Interra Flood detector Anthracite ITR401-0102

ITR401-0102 - KNX Waterflood Detector is used to detect the presence of basements, water tanks, any concealed area, or any site where water-based liquids may be leaked by infiltrating. It is used as an early warning system that provides information via the KNX bus infrastructure. It protects the users from expensive repairs and from material losses that may be caused by the damage to the goods by detecting liquid leaks early. Furthermore, with the existence of the KNX system, users have the opportunity to adjust any additional warning systems.

Main Functions:

• Module alive beacon notification 

• Eligible to alert the users via buzzer, LED, or relay output 

• The LED is available for two-color statuses 

• Alarm detection delay selections are available 

• Sensing probe that extends downward up to 25 cm 

• Suspending the alarm for desired duration feature 

• Alarm reset feature

Interra KNX  Flood detector ITR401-0002

ITR401-0002 - KNX Waterflood Detector is used to detect the presence of basements, water tanks, any concealed area, or any site where water-based liquids may be leaked by infiltrating. It is used as an early warning system that provides information via the KNX bus infrastructure. It protects the users from expensive repairs and from material losses that may be caused by the damage to the goods by detecting liquid leaks early. Furthermore, with the existence of the KNX system, users have the opportunity to adjust any additional warning systems.

 Main Functions:

• Module alive beacon notification 

• Eligible to alert the users via buzzer, LED, or relay output 

• The LED is available for two-color statuses 

• Alarm detection delay selections are available 

• Sensing probe that extends downward up to 25 cm 

• Suspending the alarm for desired duration feature 

• Alarm reset feature

Interra KNX-DMX Gateway ITR831-0001

ITR831-0001 - Interra KNX - DMX Gateway supports two-way control and can record, play and delete DMX programs. With recording times of up to 4 hours, the Interra KNX - DMX Gateway can be widely used to control devices with a built-in DMX protocol port for LED color control, such as computer light, moving head light, laser light, etc.

Main functions:

•  3 working modes: DMX recorder mode, DMX dimming mode (EIB to DMX) and DMX to EIB conversion mode (1 bit, 1 byte data point).

•  Supported communication signal: DMX512-1990, ArtNet DMX

•  Storage and playback of up to 24 programs, maximum recording time: 4 hours

•  The DMX recorder mode supports switching and dimming of up to 48 channels, i.e. control of the DMX device via the KNX system.

•  DMX to EIB conversion mode supports switching and absolute dimming via DMX signal for up to 48 channels, i.e. control of the KNX system via the DMX memory control function.

•  The DMX output signal can be used to control devices with a built-in DMX protocol port for LED color control, such as computer light, moving head light, laser light, etc. 

•  DMX input control functions for the KNX system include sequence control, scene control, switch control, relative dimming and absolute dimming.

Requires a 24V power supply (example: L&D 15W 24V power supply)