Description : 

• The ITR832-002 dual channels KNX-DALI interface device is used to provide interface between DALI and KNX installations, enabling communication between the two protocols.
• DALI devices (ballasts, etc. ECGs) connected to the line are supplied with the internal DALI power supply.
• Up to 2x64 DALI ballasts can be connected to the ITR832-002.
• With each DALI channel, 16 groups, 16 scenarios and 64 devices can be controlled. In addition, independent emergency lighting according to EN 62386-202 will be supported with the 2nd version update. Emergency lighting tests (eg function and time test) can be triggered via the KNX line. In addition, feedback on the KNX line can be sent. Each DALI device can be controlled by individually, group or broadcast control.

General functions : 

• Automatic DALI Device Addressing.
• Switching, dimming and brightness configure
• Scene configure
• KNX Bus Voltage Failure Status.
• KNX Voltage Recovery Status.
• DALI Bus Voltage Failure Status.
• DALI Voltage Recovery Status.
• Ballast and / or Lighting Error.
• Working log analysis with UDP.
• Broadcast control can be made with manually and software.
• Tunable White colour temperature control.
• RGB and RGBW colour control.

Comminssionning functions : 

• Addressing operations can be done via ETS or manual buttons as short address assignment.
• Assigning group adresses to ballasts via ETS without need additional software.
• Faulty ballast detection. 
• Faulty lighting detection.
• DALI line device selection with manual button.
• Remote software update via Ethernet connection.

Safety precautions and important notes : 

• The device may only be installed and put into operation by a qualified electrician or authorized personnel.
• For planning and construction of electric installations the appropriate specifications, guidelines and regulations in force of the respective country have to be complied.
• Special Programming: This device is designed for professional KNX and DALI installation. It can be programmed by ETS and Web Browser.
• Cable Connections: Ensure making correct connections for Black and Red wires.
• Input Voltage: The input voltage shall be 100-240 VAC.
• Installation only in dry locations and on a 35 mm DIN rail (TH 35).
• For mounting only use an appropriate equipment according to IEC 60715.
• Rain, liquid and aggressive gas should not allowed to be close to device.
• Screw down strength is less than 0.4Nm. 
• Do net get AC 240 V voltage into Bus lines, it can damage all of devices in system.

Theben - Flush-mounted 1-way DALI actuator- 4942580 - DU 1 DALI KNX

Function description

• Flush-mounted 1-way DALI actuator, KNX TP, Data Secure
• DALI-2 certified
• Interface between the DALI and the KNX bus system
• Simple commissioning of up to 30 ECGs in broadcast mode
• Control of RGB, RGBW, Tunable White or conventional luminaires
• DT-8 luminaire support
• Easy replacement of ECGs in the event of a fault
• Universal mounting thanks to the compact housing
• 2 binary inputs for potential-free contacts such as pushbuttons, switches, window contacts, temperature sensor (input I2)
• The binary input I1 is assigned to the output ex works (function test and operation even without programming)

Zennio DALIBOX Broadcast 6CH V2 ZDIDLB6V2

KNX-DALI broadcast interface module for DIN rail mounting (4.5 units). It incorporates 6 channels controlled via broadcast commands, allowing a total of 64 ballasts per channel, including color ballasts (DT8). In addition, it allows the configuration of 20 scenes/sequences per channel. It is compatible with KNX Secure. It enables manual control and has LED status indicators per channel.

Zennio DALIBOX Broadcast 4CH V2 ZDIDLB4V2

KNX-DALI broadcast interface module for DIN rail mounting (4.5 units). It incorporates 4 channels controlled via broadcast commands, including color ballasts (DT8). It allows to connect up to 250 ballasts per device, and they can be associated as whished with up to 64 ballasts per channel. In addition, it allows the configuration of 20 scenes/sequences per channel. It is compatible with KNX Secure. It enables manual control and has LED status indicators per channel.

Zennio DALI BOX Interface 64 X2 - ZDID64X2

KNX-DALI Interface for up to 64 ballasts per channel - 2 channels

KNX-DALI Interface for DIN-rail (4.5 units) with two independent DALI channels, to control up to 64 DALI ballasts per channel, which can be associated in up to 16 groups per channel. In addition to groups control, each ballast can be controlled individually, being able to create groups of ballasts via KNX. It includes a display and ETS DCA for easily addressing when a ballast is replaced, that also helps assigning ballasts to groups. Error indicators for each ballast.
It allows the lighting control of emergency (DT1) and color ballasts (DT8).
Device certified as Single Master DALI-2 controller.
It is compatible with KNX Secure

Zennio DALI BOX Interface 64 v3-ZDID64V3

KNX-DALI Interface for up to 64 ballasts per channel - 1 channel

KNX-DALI Interface for DIN-rail (4.5 units) to control up to 64 DALI independent ballasts, which can be associated in up to 64 groups. It includes a display and ETS DCA for easily addressing when a ballast is replaced, that also helps assigning ballasts to groups. Error indicators for each ballast.